Finishing up our look at the 2021 IEEE ISSCC, Forum 5 was entitled Enabling New System Architectures with 2.5D, 3D, and Chiplets. This was another clear example of a here-to-fore front-end conference now focusing on advanced packaging technologies. The session description states “The end of scaling drives innovative 2.5D, 3D and chiplet technologies to extend Moore’s law. Advancements in multi-die integration effectively reduce costs at advanced nodes while providing flexibility, modularity and heterogeneous integration…designers need to rethink system architectures to exploit these advantages.”

TSMC’s 3D Fabric

Doug Yu of TSMC discussed Foundry Solutions for 2.5 / 3D Integration”. TSMC has rebranded its leading chip packaging technologies as 3D Fabric as shown in Figure 1. If you’re not familiar with the acronyms, catch up on reading past IFTLE reports on TSMC!

2021 IEEE ISSCC
Figure 1: TSMC has rebranded chip packaging technologies as 3D Fabric. (Courtesy of TSMC)

 

SoIC is compared to 2.5D and 3D in Figure 2.

2021 IEEE ISSCC
Figure 2: There’s 2.5D and 3D, and then there is SoIC. (Courtesy of TSMC)

Yu concluded with a 3D Interconnect density roadmap for the future.

2021 IEEE ISSCC

Figure 3: Interconnect density roadmap. (Courtesy of TSMC).

Samsung’s 2021 IEEE ISSCC Presentation

Kyomin Sohn of Samsung discussed 3D stacked memory architecture with 2.5D Heterogeneous Integration. Sohn looks to 3DIC for higher performance, lower power, smaller form factor, and higher yield (3D).

2021 IEEE ISSCC
Figure 4: 3D-stacked memory architectures with 2.5D heterogeneous integration. (Courtesy of Samsung)

He sees memory stacking moving from micro-bumps to “µ-bumpless D2W bonding” (If you’re a reader of IFTLE you know this is as Ziptronix / Xperi DBI™ Ultra or hybrid bonding)

2021 IEEE ISSCC
Figure 5: Samsung’s scaling involves swapping out µbumps for hybrid bonding. (Courtesy of Samsung)

Samsung lists the following design challenge for 3D stacked high bandwidth memory:

  • Performance limitation
    • Power dissipations — Thermal throttling
    • 3D die-to-die variations — Performance loss
  • Harsh 3D operation environment
    • Thermal coupling — Memory bit-cell failure
    • Huge current consumption — IR-drop induced function failure
  • Test and validation limitation
    • KGD business model — Incomplete test
    • Limited access during debugging — Time-consuming analysis

Sony’s 2021 IEEE ISSCC Presentation

Yusuke Oike of Sony discussed Evolving Image Sensor Architecture through Stacking Devices. Stacked CMOS image sensors (CIS) are now standard in nearly all smartphone cameras. It has been nearly 15 years since the industry began to adopt back side illumination, which was followed by the separation and stacking of pixels and circuits. Connections were accomplished by direct copper – copper hybrid bonding technology making CIS the first application to use this technology. (see Samsung discussion above)

2021 IEEE ISSCC
Figure 6: Sony was the first to integrate DBI hybrid bonding into its CIS. (Courtesy of Sony).

Then a few years ago Sony was the first to include DRAM into the stack for its slow-motion capture applications.

2021 IEEE ISSCC
Figure 7: Another Sony first: TSVs in its DRAM stacks.

Oike then described how sensor architecture is evolving using 3D technologies:

  • More advanced pixel circuitry
  • Stacked pixel circuitry
  • Event-based vision sensing
  • Pixel-parallel ADC architecture
  • SPAD-based photon counting
  • Hybrid Integration on Si
  • SWIR InGaAs photodetector
  • Integrating more intelligent processor with sensor
  • Intelligent vision sensor

For example, the use of InGaAs sensors for future automated inspection and security cameras.

2021 IEEE ISSCC
Figure 8: 3D ICs are now prevalent in automated inspection and security cameras. (Courtesy of Sony).

For all the latest in Advanced Packaging stay linked to IFTLE……………………….

Phil Garrou

Dr Phil Garrou is an Advanced Packaging subject matter expert for DARPA and the DoD…

View Phil's posts

Become a Member

Media Kit

Login